PINPOINT TEST E : The Adjustable Pedals are inoperative or Do Not Operate Correctly - Using the Memory SET Switch Buttons or the RKE Transmitter
- E1 CHECK THE ADJUSTABLE PEDAL OPERATION WITH THE ADJUSTABLE PEDAL SWITCH
- Press the adjustable pedal switch in each direction for more than one second and observe the adjustable pedals.
Do the adjustable pedals operate for more than one second in the direction selected using the switch?
Yes GO to E2. No If the pedals do not move at all using the switch, GO to Pinpoint Test D . If the pedals only move in 1 second intervals regardless of button operation GO to Pinpoint Test C . - E2 CHECK THE MEMORY SYSTEM OPERATION
- Set a memory position for the driver seat, exterior mirrors and adjustable pedals to memory SET switch button 1. REFER to Seating 1st Row .
- Select PARK.
- Press the memory SET switch button 1 and observe:
- Driver seat
- Exterior mirrors
- Adjustable pedals
Do all 3 items move when the button is pressed?
Yes GO to E3. No If all 3 items do not move, Refer to 'Seating 1st Row', Go to Pinpoint Test J to diagnose the memory SET switch. If only the adjustable pedals do not move, GO to E4. If only the driver seat does not move, Refer to 'Seating 1st Row', Go to Pinpoint Test J . If only the exterior mirrors do not move, Refer to 'Rear View Mirrors', Go to Pinpoint Test D . - E3 CHECK THE RKE OPERATION
- Set a memory position in the RKE for the driver seat, exterior mirrors and adjustable pedals. REFER to Handles, Locks, Latches and Entry Systems With Intelligent Access (IA) .
- Select PARK.
- Press the unlock button on the RKE transmitter/Intelligent Access (IA) key and observe:
- Driver seat
- Exterior mirrors
- Adjustable pedals
Do all 3 items move when the button is pressed?
Yes The system is operating correctly at this time. No If all 3 items do not move, Refer to article 'Handles, Locks, Latches and Entry Systems With Intelligent Access (IA)', Go to Pinpoint Test J . If only the adjustable pedals do not move, GO to E4. If only the driver seat does not move, REFER to Seating 1st Row , Symptom Chart: Seating - Memory. If only the exterior mirrors do not move, REFER to Rear View Mirrors , Symptom Chart: Rear View Mirrors - Exterior, Memory. - E4 CHECK FOR DSM OR BCM DTCs
- Ignition ON
- Using a diagnostic scan tool, carry out the DSM self-test.
- Using a diagnostic scan tool, carry out the BCM self-test.
- Record any DTCs retrieved from the DSM or the BCM.
Was DTC U0140 retrieved from the DSM or U0212:00 retrieved from the BCM-B ?
Yes If DTC U0140 is retrieved from the DSM, Refer to 'Seating 1st Row', Go to Pinpoint Test AN . If DTC U0212:00 is retrieved from the BCM, Refer to 'Multifunction Electronic Modules', Go to Pinpoint Test AJ . No GO to E5. - E5 CHECK THE ADJUSTABLE PEDAL MOTOR AND HALL-EFFECT SENSOR CIRCUITS FOR A SHORT TO VOLTAGE
- Ignition OFF.
- Disconnect Adjustable Pedal Motor C2003 .
- Disconnect SCCM C2414C .
- Disconnect SCCM C2414B .
- Ignition ON.
- Measure:
Positive Lead Measurement / Action Negative Lead C2003-1 Ground C2003-2 Ground C2003-3 Ground C2003-4 Ground
Is any voltage present?
Yes REPAIR the affected circuit. No GO to E6. - E6 CHECK THE ADJUSTABLE PEDAL MOTOR AND HALL-EFFECT SENSOR CIRCUITS FOR A SHORT TO GROUND
- Ignition OFF.
- Measure:
Positive Lead Measurement / Action Negative Lead C2003-1 Ground C2003-2 Ground C2003-3 Ground C2003-4 Ground
Are the resistance values greater than 10, 000 ohms?
Yes GO to E7. No REPAIR the affected circuit. - E7 CHECK THE ADJUSTABLE PEDAL MOTOR CIRCUITS FOR AN OPEN
Are the resistances less than 3 ohms?
Yes GO to E8. No REPAIR the affected circuit. - E8 CHECK THE ADJUSTABLE PEDAL MOTOR HALL-EFFECT SENSOR CIRCUITS FOR AN OPEN
Are the resistances less than 3 ohms?
Yes GO to E9. No REPAIR the affected circuit. - E9 CHECK THE ADJUSTABLE PEDAL MOTOR AND HALL-EFFECT SENSOR CIRCUITS FOR A SHORT TOGETHER
- Measure:
Positive Lead Measurement / Action Negative Lead C2003-4 C2003-2 C2003-4 C2003-3 C2003-4 C2003-1 C2003-2 C2003-3 C2003-2 C2003-1 C2003-3 C2003-1
Are the resistance values greater than 10, 000 ohms?
Yes CONFIGURE the SCCM using As-built data and TEST the system for normal operation. If the adjustable pedals do not operate correctly, INSTALL a new adjustable pedal motor and bracket assembly. REFER to Acceleration Control . No REPAIR the affected circuit. - Measure:
