Pinpoint Test P : B103C

NOTE: When taking measurements at DCSM harness connectors, do not insert the electrical probes into the female connector pins. Inserting the probes into connector pins can cause intermittent or open electrical connections after reassembly resulting in DTCs and system failure. Touching the tip of these connector pins is recommended instead.

P1 CHECK THE TED CIRCUITS FOR AN OPEN

WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

Ignition OFF.

Disconnect: Driver Seat Side Air Bag C3051 .

Disconnect: Passenger Seat Side Air Bag C339 .

Disconnect: DCSM C3265A .

Disconnect: Driver Cushion TED C3035 .

Disconnect: Driver Backrest TED C3034 .

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3265A-G	Courtesy of FORD MOTOR COMPANY	C3035-1
C3265A-H	Courtesy of FORD MOTOR COMPANY	C3035-3

Positive Lead	Measurement / Action	Negative Lead
C3265A-J	Courtesy of FORD MOTOR COMPANY	C3034-1
C3265A-K	Courtesy of FORD MOTOR COMPANY	C3034-3

Are the resistances less than 3 ohms?

Yes	GO to P2.
No	REPAIR the affected circuit. GO to P5.

P2 CHECK THE TED CIRCUITS FOR A SHORT TO VOLTAGE

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C3265A-G	Courtesy of FORD MOTOR COMPANY	Ground
C3265A-H	Courtesy of FORD MOTOR COMPANY	Ground
C3265A-J	Courtesy of FORD MOTOR COMPANY	Ground
C3265A-K	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present on any circuits?

Yes	REPAIR the affected circuit. GO to P5.
No	GO to P3.

P3 CHECK THE RESISTANCE OF THE TEDs

Ignition OFF.

Measure the component side resistance:

Positive Lead	Measurement / Action	Negative Lead
Driver Seat Backrest TED C3034-1, Component Side	Courtesy of FORD MOTOR COMPANY	Driver Seat Backrest TED C3034-3, Component Side

Positive Lead	Measurement / Action	Negative Lead
Driver Seat Cushion TED C3035-1, Component Side	Courtesy of FORD MOTOR COMPANY	Driver Seat Cushion TED C3035-3, Component Side

Are the resistances between 0.9 and 10 ohms?

Yes	GO to P4.
No	If the resistance of the backrest TED was not between 0.9 and 10 ohms, INSTALL a new backrest TED. Refer to Seat Backrest Thermo-Electric Device (TED) . GO to P5. If the resistance of the cushion TED was not between 0.9 and 10 ohms, INSTALL a new cushion TED. Refer to Seat Cushion Thermo-Electric Device (TED) . GO to P5.

P4 CHECK FOR CORRECT DCSM OPERATION

Ignition OFF.

Disconnect and inspect all DCSM connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins as necessary
- pushed-out pins - install new pins as necessary

Reconnect the DCSM connectors. Make sure they seat and latch correctly.

Connect: Driver Seat Backrest TED C3034 .

Connect: Driver Seat Cushion TED C3035 .

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable TSBs. If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no TSBs address this concern, INSTALL a new DCSM. Refer to Dual Climate Controlled Seat Module (DCSM) . GO to P5.
No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. GO to P5.

P5 CHECK FOR SRS DTCs

Ignition OFF.

Connect: Driver Seat Side Air Bag C3051 .

Connect: Passenger Seat Side Air Bag C339 .

Connect: DCSM C3265A (if previously disconnected).

Connect: Driver Seat Backrest TED C3034 .

Connect: Driver Seat Cushion TED C3035 .

Ignition ON.

Using a diagnostic scan tool, clear the RCM DTCs.

Cycle the ignition OFF then ON.

Using a diagnostic scan tool, perform RCM self-test.

Are any RCM DTCs retrieved during self-test?

Yes	REFER to Supplemental Restraint System for pinpoint test direction.
No	The repair is complete. RETURN the vehicle to the customer.