LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2015 >> Explorer Limited, 3.5L Eng VIN 8, AWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Window Motors & Regulators >> Window Glass, Window Frames And Window Mechanisms >> Removal And Installation >> Window Glass - Rear Quarter >> Installation

Window Glass - Rear Quarter: Installation

    NOTE: For additional material guidelines, refer to the manufacturer's installation information.

  1. 1.
    Dry fit the rear quarter window glass to the existing urethane adhesive bead on the body pinch weld. Align the rear quarter window glass in the opening for a uniform fit.

  1. 2.

    Use a non-permanent pencil to make alignment marks on the rear quarter window glass at the setting blocks (if equipped) and the body to aid in the installation alignment of the rear quarter window glass.

  1. 3.

    Remove the rear quarter window glass.
    NOTE: Avoid scratching the pinch weld. Repair all minor scratches or exposed metal on the pinch weld following manufacturer's instructions. Use the same brand pinch weld primer, glass primer and urethane adhesive.
    WARNING: Repair any corrosion found on the pinch weld. The pinch weld is a structural component of the vehicle. Corrosion left unrepaired may reduce the structural integrity of the vehicle. Failure to follow this instruction may result in serious injury to vehicle occupant(s).

  1. 4.

    Using an appropriate tool, trim the urethane adhesive leaving a 1 mm to 2 mm (0.04 in to 0.08 in) base of original equipment urethane adhesive on the pinchweld.

GFD37616Courtesy of FORD MOTOR COMPANY

  1. 5.

    Using a soft brush or vacuum, remove any dirt or foreign material from the pinch weld.

  1. 6.

    Clean the inside of the rear quarter window glass surface with glass cleaner.
    NOTE: Be sure to use the same brand and cure-rate products for the urethane adhesive and glass primer. Do not mix different brands of urethane adhesive and glass primer. REFER to Material Specifications .

  1. 7.
    If installing a new rear quarter window glass, apply glass primer according to manufacturer's instructions. Allow at least 6 minutes to dry.

  1. 8.

    Cut the urethane adhesive applicator tip to specification.
GFD37617Courtesy of FORD MOTOR COMPANY
    NOTE: Use either a high-ratio, electric or battery-operated caulk gun that will apply the urethane adhesive with less effort and continuous bead.

  1. 9.
    Apply urethane adhesive on top of the existing trimmed urethane adhesive bead on the pinch weld, starting and ending at the bottom of the rear quarter window glass opening near the center, making sure there are no gaps in the bead.
    NOTE: Before positioning the rear quarter glass, open vehicle windows to prevent the air pressure of closing doors from affecting the urethane adhesive bond.
    WARNING: Improper curing of the urethane adhesive may adversely affect glass retention, which is important for restraint system performance during a crash. Carefully follow the urethane adhesive manufacturer's curing instructions. Do not drive the vehicle until the urethane adhesive seal has cured. Failure to follow these instructions may result in serious injury to vehicle occupant(s) during a crash.

  1. 10.

    Install the rear quarter window glass on the vehicle aligning it with the markings made previously.

    NOTE: The urethane adhesive must cure for a minimum of one hour before testing for air or water leaks.

  1. 11.
    After the urethane adhesive has cured, check the rear quarter window glass seal for air or water leaks through the urethane adhesive bead and add urethane adhesive as necessary.

  1. 12.

    Install the D-pillar trim panel. REFER to Interior Trim and Ornamentation .

  1. 13.

    Install the C-pillar trim panel. REFER to Interior Trim and Ornamentation - Without Inflatable Safety Belts or REFER to Interior Trim and Ornamentation - With Inflatable Safety Belts. .
scientia non olet · About LEMON Manuals