Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data and any DTCs.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go to 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE REAR VIDEO CAMERA
1. Turn the ignition off.
2. Disconnect the Rear Video Camera harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Replace the Rear Camera in accordance with the Service Information. Refer to CAMERA, REAR, REMOVAL AND INSTALLATION or CAMERA, REAR INTERIOR, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE STEERING COLUMN CONTROL MODULE (SCCM)
1. Turn the ignition off.
2. Disconnect the SCCM harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 4
  No
  - Replace the Steering Column Control Module (SCCM) in accordance with the Service Information. Refer to MODULE, STEERING COLUMN CONTROL (SCCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE HANDS FREE RELEASE MODULE (HFRM)
1. Turn the ignition off.
2. Disconnect the HFRM harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 5
  No
  - Replace the Hands Free Release Module (HFRM) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE LEFT HANDS FREE SLIDING DOOR MODULE (HFSD-LT)
1. Turn the ignition off.
2. Disconnect the HFSD-LT harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 6
  No
  - Replace the Left Hands Free Sliding Door Module (HFSD-LT) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE RIGHT HANDS FREE SLIDING DOOR MODULE (HFSD-RT)
1. Turn the ignition off.
2. Disconnect the HFSD-RT harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
6. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 7
  No
  - Replace the Right Hands Free Sliding Door Module (HFSD-RT) in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (D403) LIN BUS 3 CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Disconnect the BCM C5/E harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (D403) LIN 3 Bus circuit at the BCM C5/E harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the short to voltage on the (D403) LIN 3 Bus circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 8
CHECK THE (D403) LIN BUS 3 CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Check for continuity between ground and the (D403) LIN 3 Bus 3 circuit at the BCM C5/E harness connector.
  Is there continuity between ground and the (D403) LIN 3 Bus 3 circuit?
  
  Yes
  - Repair the short to ground in the (D403) LIN Bus 3 circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 9
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.