Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
2. With the scan tool, read DTCs and record on the repair order.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (K533) VVL SOLENOID 2/1 DRIVER CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Disconnect the VVL Solenoid 2/1 harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (K533) VVL Solenoid 2/1 Driver circuit at the VVL Solenoid 2/1 harness connector.
  NOTE:
  There should be no voltage present unless you have a short to voltage, except for a brief period immediately after turning ignition on.
  
  Is there any voltage present?
  
  Yes
  - Go To 3
  No
  - Go To 4
CHECK FOR THE (K533) VVL SOLENOID 2/1 DRIVER CIRCUIT SHORTED TO ANOTHER VOLTAGE SUPPLY CIRCUIT
1. Turn the ignition off.
2. Disconnect the PCM C2 harness connector.
  CAUTION:
  Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.
3. Connect the (special tool #10436, Adapter, GPEC Diagnostic).
4. Check for continuity between the (K533) VVL Solenoid 2/1 Driver circuit and all other circuits at the GPEC Adaptor.
  Is there continuity between the (K533) VVL Solenoid 2/1 Driver circuit and any other circuit?
  
  Yes
  - Repair the (K533) VVL Exhaust Solenoid 2/1 Driver circuit for a short to the circuit that showed continuity.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs and record on the repair order.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.