Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. Perform any Service Bulletins that may apply.
2. Turn the ignition on.
3. With the scan tool, read the ABS DTCs and record on the vehicle repair order.
4. With the scan tool, erase ABS DTCs.
5. Cycle the ignition from off to on.
6. Pull the EPB Switch up to apply the Electric Parking Brakes.
7. Press the brake pedal firmly and hold.
8. Push the EPB Switch down to release the Electric Parking Brakes.
9. Release the brake pedal.
10. Cycle the ignition from off to on.
11. With the scan tool, read ABS DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - The conditions that caused this code to apply are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring harness and electrical connectors.
  - Perform the EPB VERIFICATION TEST. Refer to EPB VERIFICATION TEST .
CHECK PARKING BRAKE SWITCH CONNECTOR/TERMINAL FOR DAMAGE
NOTE:
Check all terminals for broken, bent, pushed out, or corroded terminals.
1. Turn the ignition off.
2. Inspect the Parking Brake Switch for proper mounting.
3. Inspect the Parking Brake Switch for correct mechanical operation.
4. Inspect the Parking Brake Switch harness and connector.
  Were any problems found?
  
  Yes
  - Repair as necessary.
  - Perform the EPB VERIFICATION TEST. Refer to EPB VERIFICATION TEST .
  No
  - Go To 3
PARKING BRAKE SWITCH
1. Turn the ignition off.
2. Replace the Parking Brake Switch in accordance with the Service Information. Refer to SWITCH, ELECTRIC PARK BRAKE, REMOVAL AND INSTALLATION . Perform the EPB VERIFICATION TEST. Refer to EPB VERIFICATION TEST .
3. Turn the ignition on.
4. With the scan tool, read ABS DTCs.
  Does the DTC remain active?
  
  Yes
  - Go To 4
  No
  - Test complete, the condition or conditions that originally apply this DTC are not present at this time.
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect the ABS Module harness connector.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Connect the ABS Module harness connector. Be certain that the harness connector is fully seated and the connector lock is fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect the related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
  WARNING:
  To avoid possible serious or fatal injury, check brake capability is available before road testing.
9. Using the recorded Event and Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that apply the DTC.
10. With the scan tool, read ABS Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Anti-lock Brake System (ABS) Module in accordance with the Service Information. Refer to MODULE, ANTI-LOCK BRAKE SYSTEM (ABS), REMOVAL AND INSTALLATION .
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Perform ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  - Test complete.