LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Chrysler >> 2021 >> Voyager LXi, Gas >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Accessories Control Systems >> (Rear Right Door Module (DMRR) - Electrical Diagnostics) >> DTC Troubleshooting >> B19E1-11 Sliding Door Handle Switch-Circuit Short To Ground >> Diagnostic Test

Diagnostic Test

  1. CHECK FOR AN ACTIVE DTC 
    1. Turn the ignition on.
    2. With the scan tool, create a Vehicle Scan Report and attach it to the repair order.
    3. With the scan tool, record and any power sliding door inhibitors.
    4. Erase the DTCs.
    5. Turn the ignition off, wait 10 seconds, then turn the ignition on.
    6. Attempt to operate the Right Power Sliding Door from the door handle.
    7. With the scan tool, read the DMRR DTCs.

      Is the DTC active?

      Yes 

      • Go To  2

      No 

  2. CHECK THE RIGHT DOOR IN/OUT HANDLE FOR STICKING 
    1. Check the outside handle and then the inside handle for sticking.

      Is there a sticking problem?

      Yes 

      No 

      • Go To  3
  3. CHECK THE (Q54) RIGHT DOOR IN/OUT HANDLE SWITCH SENSE CIRCUIT FOR A SHORT TO GROUND 
    1. Turn the ignition off.
    2. Disconnect the Right Rear Door Module C4 harness connector.
    3. Check for continuity between ground and the (Q54) Right Door In/Out Handle Switch Sense circuit at the Right Rear Door Module C4 harness connector.
      NOTE:

      Be careful not to spread the terminals in the connector.

      Is there continuity between ground and the (Q54) Right Door In/Out Handle Switch Sense circuit?

      Yes 

      • Repair the (Q54) Right Sliding Door Release Handle circuit for a short to ground.
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK THE (Q54) RIGHT DOOR IN/OUT HANDLE SWITCH SENSE CIRCUIT FOR A SHORT TO THE (Q780) RIGHT POWER SLIDING DOOR MUX RETURN CIRCUIT 
    1. Check for continuity between the (Q54) Right Door In/Out Handle Switch Sense circuit and the (Q780) Right Power Sliding Door Mux Return circuit at the Door Module C4 connector.
      NOTE:

      Be careful not to spread the terminals in the connector.

      Is there continuity between the (Q54) Right Door In/Out Handle Switch Sense circuit and the (Q780) Right Power Sliding Door Mux Return circuit?

      Yes 

      • Repair the (Q54) Right Door In/Out Handle Switch Sense circuit for a short to the (Q780) Right Power Sliding Door Mux Return circuit.
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

      • Go To  5
  5. CHECK THE RIGHT REAR DOOR LATCH ASSEMBLY 
    1. Replace the Right Rear Door Latch Assembly in accordance with service information. Refer to LATCH, REAR, REMOVAL AND INSTALLATION .
    2. Reconnect all Right Rear Door Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    3. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    4. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    5. Erase the DTCs.
    6. Turn the ignition off, wait 10 seconds, then turn the ignition on.
    7. Attempt to operate the Right Power Sliding Door from the door handle.
    8. With the scan tool, read the DMRR DTCs.

      Did the DTC return?

      Yes 

      • Go To  6

      No 

  6. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all Right Rear Door Module harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Perform a terminal drag test on each connector terminal to verify proper terminal tension.

      Repair any conditions that are found.

    5. Reconnect all Right Rear Door Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Using the recorded Vehicle Scan Report, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
    10. With the scan tool, read DMRR DTCs.

      Did the DTC return?

      Yes 

      • Replace the Right Rear Door Module in accordance with the Service Information. Refer to REAR .
      • Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .

      No 

scientia non olet · About LEMON Manuals