Diagnostic Test

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. With the scan tool, run a vehicle Scan Report, or record the Environmental Data related to the DTCs.
3. NOTE: A front door must remain open whenever checking or erasing Radio DTCs.
4. With the scan tool, record and erase the Radio DTCs.
5. Cycle the ignition switch from on to off, wait five seconds and then back to on.
6. Turn the Radio on and set the volume to 25.
7. Adjust the speakers to the front and center.
8. With the scan tool, read the active Radio DTCs.
NOTE:
A front door must remain open whenever checking or erasing Radio DTCs.

Did the DTC return?

Yes
- Go To 2
No
- Perform the appropriate INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE ANTENNA CONNECTION
1. Turn the ignition off.
2. Disconnect the Antenna connector at the back of the Radio.
3. Inspect the Antenna connections.
  Are the Antenna connections clean and secure?
  
  Yes
  - Go To 3
  No
  - Repair the Antenna connection as needed.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE ANTENNA AND CABLE
1. Connect the Radio Diagnostic Tool (special tool #9977-6-13, Adapter, Long RF RG-58 Fakra) and (special tool #9977-6-CELL-LTE, Adapter, Cellular Antenna Diagnostic) to the Cellular Antenna connection on the back of the Radio.
2. Make sure one of the front doors is still open.
3. Turn the ignition on.
4. Using the scan tool, erase the DTCs.
5. Turn the Radio on.
6. Using the scan tool, read Radio DTCs.
  Is the DTC active?
  
  Yes
  - Go To 5
  No
  - Go To 4
TEST THE CELLULAR ANTENNA CABLE
1. Turn the ignition off.
2. Disconnect the vehicles Cellular Antenna cable at the Cellular Antenna.
  NOTE:
  Special tool 9977-6-13 should still be connected at the back of the Radio during this test.
3. Connect the (special tool #9977-6-13, Adapter, Long RF RG-58 Fakra) to the vehicles Cell Antenna.
4. Make sure one of the front doors is still open.
5. Turn the ignition on.
6. Using the scan tool, erase the DTCs.
7. Turn the Radio on.
8. Using the scan tool, read Radio DTCs.
  Is the DTC active?
  
  Yes
  - Replace the Cellular Antenna in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Use the Radio Diagnostic Tool (special tool #9977-6-13, Adapter, Long RF RG-58 Fakra) to locate the open circuit, repair or replace the Cellular Antenna cable as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all Radio harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all Radio harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read Radio DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Radio in accordance with the Service information. Refer to MODULE, RADIO RECEIVER, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.