Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. Turn the ignition on.
2. With the scan tool, create a Vehicle Scan Report and attach it to the repair order.
3. Lower the passenger door window.
4. Turn the ignition on to off three times.
5. Close then open the passenger door.
6. Turn the ignition on.
7. Wait one minute.
8. With the scan tool, read PDM DTCs.
  Is the DTC active?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (M44) PASSENGER DOOR COURTESY LAMP DRIVER CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Remove the inner door panel trim in accordance with the Service Information.
3. Disconnect the Passenger Door Module C5 harness connector.
4. Turn the ignition on.
5. Measure the voltage between ground and the (M44) Passenger Door Ambient Lamp Driver circuit at the Passenger Door Module C5 harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the (M44) Passenger Door Courtesy Lamp Driver circuit for a short to voltage.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (M44) PASSENGER DOOR COURTESY LAMP DRIVER CIRCUIT FOR AN OPEN
1. Turn the ignition off.
  NOTE:
  Make sure the Passenger Door Courtesy (puddle/trim) Lamp connector is still connected.
2. Turn the ignition on.
3. Connect a fused jumper wire between B(+), to the (M44) Passenger Door Courtesy Lamp Driver circuit at the Passenger Door Module C5 harness connector.
4. Connect a jumper wire between ground and the (M36) Passenger Door Lighting Return circuit at the Passenger Door Module C5 harness connector
  Does the Passenger Door Courtesy (puddle/trim) Lamp illuminate brightly?
  
  Yes
  - Refer to 6.
  No
  - Go To 4
CHECK THE (M44) PASSENGER DOOR COURTESY LAMP DRIVER CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Disconnect the Passenger Door Puddle Lamp harness connector.
3. Measure the resistance of the (M44) Passenger Door Courtesy Lamp Driver circuit between the PDM C5 harness connector and the Passenger Door Courtesy (puddle/trim) Lamp harness connector at the Passenger Door Module C5 harness connector.
  Is the resistance below 2.0 Ohms?
  
  Yes
  - Go To 5
  No
  - Repair the (M44) Passenger Door Courtesy Lamp Driver circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (M36) PASSENGER DOOR LIGHTING RETURN CIRCUIT FOR A OPEN
1. Measure the resistance of the (M36) Passenger Door Lighting Return circuit between the Passenger Door Module C5 harness connector and the Passenger Door Courtesy (puddle/trim) Lamp harness connector.
  Is the resistance below 2.0 Ohms?
  
  Yes
  - Replace the Passenger Door Courtesy (puddle/trim) Lamp.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Repair the (M36) Passenger Door Lighting Return circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all Passenger Door Module harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all Passenger Door Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Vehicle Scan Report, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read PDM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Passenger Door Module in accordance with the Service Information. Refer to MODULE, DOOR (DDM/PDM), REMOVAL AND INSTALLATION
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.