Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
2. With the scan tool, read DTCs and record on the repair order.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (K532) VVL SOLENOID 1/2 DRIVER CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the VVL Solenoid 1/2 harness connector.
3. Disconnect the PCM C2 harness connector.
4. Check for continuity between ground and the (K532) VVL Solenoid 1/2 Driver circuit at the VVL Solenoid 1/2 harness connector.
  Is there continuity between ground the (K532) VVL Solenoid 1/2 Driver circuit?
  
  Yes
  - Repair the (K532) VVL Solenoid 1/2 Driver circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK FOR THE (K532) VVL SOLENOID 1/2 DRIVER CIRCUIT SHORTED TO THE (Z904) GROUND CIRCUIT
1. Check for continuity between the (K532) VVL Solenoid 1/2 Driver circuit and the (Z904) Ground Circuit at the VVL Solenoid 1/2 harness connector.
  Is there continuity between the (K532) VVL Solenoid 1/2 Driver circuit and the (Z904) Ground Circuit?
  
  Yes
  - Repair the short between the (K532) VVL Solenoid 1/2 Driver circuit and the (Z904) Ground Circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE VVL SOLENOID
1. Measure the resistance of the VVL Solenoid (component). Remove the VVL Solenoid if necessary to gain access to the terminals and ensure a proper reading.
  NOTE:
  The resistance reading through a good VVL Solenoid that is not open or internally shorted is 12.0 Ohms +/- 2.0 Ohms.
  
  Is the resistance reading as described above?
  
  Yes
  - Go To 5
  No
  - Replace the VVL Solenoid in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs and record on the repair order.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.